Dunlap Woodcrafts

This high quality stock is a composite of four original stocks and can be finished to the pattern carved or can be varied to copy a variety of slightly smaller original individual stocks. Since the 1795 musket parts were all hand-made, almost all parts vary in size from one musket to another. Therefore, only the lock internals are inlet, leaving enough wood to final inlet the variety of original lock plates. The inletting for the buttplate and trigger guard is undersize and requires detailed fitting of these parts. The stock forearm is long enough to permit the use of up to a 45-inch long barrel.

This high quality stock is a composite of four original stocks and can be finished to the pattern carved or can be varied to copy a variety of slightly smaller original individual stocks. Since the 1795 musket parts were all hand-made, almost all parts vary in size from one musket to another. Therefore, only the lock internals are inlet, leaving enough wood to final inlet the variety of original lock plates. The inletting for the buttplate and trigger guard is undersize and requires detailed fitting of these parts. The stock forearm is long enough to permit the use of up to a 45-inch long barrel.

Each of these stocks were copied from excellent quality original guns, with the barrel final fit and the remainder of the other parts inlet .20 to .035 undersize to permit a better final fit of original parts.

Each of these stocks was copied from excellent quality original guns with all parts final fit except the locks on the 1816 model, which are cut .040 undersize to permit the final fitting of the original locks which varied slightly because of manual reproduction. Special orders for extra wood remaining around the rear portion of the lock mortise on the 1842, to finish the Model 1835 variation, are available upon request.

This stock was copied from an excellent quality original 1819 model. It has been inletted for the barrel, receiver. Buttplate and ramrod- channel. By requesting that the inletting for the trigger guard plate be omitted, the stock can be reworked to fit the M-1841 Hall. Additionally, this stock can be used for the 1836 Hall Carbine by requesting that the trigger plate not be inletted. By shortening the forearm and using a modified dovetail bit, the ramrod channel can be fitted for the ramrod bayonet.

This stock is for the one rifle and has everything final fit except the buttplate, the band-keeper springs and the nosecap. The stock can be special- ordered without to patchbox and sideplate to produce the Confederate model, and/or with the metal parts opening undersize to accommodate reproduction parts.

This copy of a fine German infantry musket is carved with the barrel channel to dimension and the inletting for the other parts approximately .035 undersize allow for the minor variations in the original parts dimensions between the various German armories. The stock will be carved from American-grown beech unless otherwise specified. Due to major problems trying to duplicate the semi-enclosed ramrod channel, all stocks will be cut with a 1/4 in wide ramrod channel and drilled with a 1/4 in ramrod drill. For those individuals trying to exactly duplicate the original stocks, we will special cut for a smaller ramrod channel, but will not drill for the ramrod hole.

This copy of a fine Austrian weapon, which was available in both rifled and smooth-bore models, is carved to the dimension of the original parts. The stock will be carved from American-grown beech unless otherwise specified. Due to major problems trying to duplicate the semi-enclosed ramrod channel, all stocks will be cut with a 1/4 in wide ramrod channel and drilled with a 1/4 in ramrod drill. For those individuals trying to exactly duplicate the original stocks, we will special cut for a smaller ramrod channel, but will not drill for the ramrod hole.

This stock is for the one rifle and has everything final fit except the buttplate, the band-keeper spring and the nosecap. This stock can be special ordered to make the long-range sight model, or without the patchbox and for the 1863 lock to make the Fayetteville rifle

This stock is for the one gun and requires minor inletting in the lock area for the 1855 humpback lock. All other areas of the stock are cut the same as the 1861 stock.

This stock was copied from an excellent quality original rifle stock. All original parts should fit real well. All parts except the buttplate, band keeper springs and nosecap are final fit.

This stock will make all of the Springfield 3-Band rifled musket stock patterns from 1861 – 1865. Everything is cut in place except the final fit of the buttplate, the spoon indention for the 1861 ramrod, the band-keeper spring and the nosecap. With a minimum amount of inletting it will also make the 1855 3-Band Springfield stock without the patchbox and the Richmond musket. This stock is also used to make both the 1855 and the 1861-65 artillery models. This stock is also used to stock the 1866 and 1867 Allen conversions of the early Springfield trapdoors.

This is a direct copy of a high quality custom reproduction of an original carbine. All parts except the buttplate, breech and band-keeper spring are press-in fit with original parts.

This is a direct copy of an excellent quality original stock. All parts except the buttplate and breech are press-in fit with original parts.

These stocks were copied directly from an excellent quality original rifled-musket. This stock also is a perfect fit for the L&GY and Amoskeg. This stock also is used to make the 1861 Special Artillery model by requesting that the middle band area not be cut. Note, this 1861 special stock does not fit the 1861 Springfield or other contract muskets except as noted above. The tang on the buttplate for this stock is narrower than the standard 1861 3-band musket, the lock is different, and the buttstock shape is different.

This stock was copied from an excellent reproduction rifle after detailed comparison of all stock dimensions with an excellent quality original rifle.

This stock was copied from an original Zouve stock; however, because of the slight variation in the original lock parts, the lock mortise is cut approximately .040 undersize. Most Italian reproduction parts will fit real well in this stock.

The stock was copied from an original Tower stock, and is cut close enough to restore original rifles and to fit most Parker Hale and other Italian reproduction parts.

The stock was copied from an original high quality Tower stock with the Barnett conversion.

The stock was copied from an original Tower stock and is cut close enough to restore original guns or fit most Parker Hale and other Italian reproduction parts.

This is a composite stock that with minimum handwork can make fine copies of either model.

These stocks were copied from a high quality original rifle. The 1868 stock needs only very minor inletting to lengthen the breech area, and can be used to fit both models. All other parts are inletted to dimension and should be press-in fit with original parts.

Each of these stocks were copied directly from an excellent quality original stock and should be press-in fit with original parts, and only need final fitting of the buttplate and breech area. The 1884 model can be ordered with the ramrod channel expanded for the ramrod bayonet.

Each of these stocks will be copied directly from a very good to excellent quality original stocks. Only the buttplate and the breech area require final fitting. The 1896 and 1989 stocks are currently available, and the 1892 stock is being reworked and should be available by early summer 2000.

This stock was copied directly from an excellent condition original stock.

The following short stocks are currently available or will be available as specified.

These stocks were copied directly from excellent quality original stocks. The buttstocks are available with and without the patchbox and with and without the inletting for the saddle ring for the carbine. Forearms available include the short carbine forearm and the long rifle forearm.

These stocks were copied from excellent quality original pieces and require only minimal fitting

These pieces are being copied directly from good quality original pieces and will only require minimal fitting of the buttstocks and forearms to the action. It is anticipated that these stocks will be available by the fall 1998 National Skirmish.

Each of these stocks were copied directly from excellent quality original stocks.

These stocks will be copied directly from excellent quality original stocks. We anticipate that the stocks will be available by mid –to- late 2000.

These stocks were copied directly from a high quality original stock. The stocks require final fitting of the buttplate and the receiver area.

The stocks are cut to dimension to be used to replace the one-piece and two-piece reproduction musket stocks for the Italian reproduction models. Copies of the forearm of this stock are being used to restore original stocks.

These stocks are provided as replacement stocks for the Italian mass-produced Brown Bess Muskets. The stocks are provided in two versions. The first is a detailed direct copy of the reproduction musket. The second variety has approximately ¾ of an inch more drop and makes the finished gun much more comfortable to handle and shoot. The only modification to the original Italian hardware is to slightly bend the brass triggerguard to accommodate the slight increase in drop. Both variations are nearly completely inletted for all of the hardware. Available in black walnut, black cherry and straight-grained ash at the same price.

Complete stocks for all of the original Rifles and Muskets - $275.00 each; three or more complete stocks mix or match, $225.00 each.

Brown Bess replacement stocks in American black walnut $295.00. This model can also be provided in European walnut military grade from $395.00 and higher, depending on the grade of the piece of wood.

Forearms for all of the original Rifles and Muskets $75.00 each; three or more total stocks or forearms, mix or match, $60.00 each.

Trapdoor carbine stocks $240.00 each; three or more total stocks mix or match, $200.00 each.

Shipping costs for one or two stocks is $18.50. For three or more stocks, shipping and insurance will be charged based on Fedex ground costs, plus $3.00 per shipment.

These stocks are all heartwood straight-grained black walnut. Stocks with figured Black Walnut for officer or presentation-grade wood are available; prices vary depending on the quality of the figure. Prices for Special Order variations of the above patterns, additional new patterns or other varieties of wood, including English walnut are available upon request.